My Sunrise

    • Motion Detector

    Function overview

    • Detects infrared signatures to identify movement in the protected area and signals the base station to trigger an alarm

    • Typical detection range: Up to 12 m at mounting height 2.4 m

    • Pet immunity: Ignores pets up to 25 kg

    • Two-part design: Cover (electronics & optics) and base (mounting)

    • LED indicator

      • Lights for two seconds for motion detection when battery is low or button is pressed (battery low).

      • No LED indication with normal battery level (except in Test mode)

    • Battery

      • Uses 2 × 1.5 V AA alkaline batteries (pre-installed, with insulator)

      • Low battery → app message + optional push notification, call, SMS, email

      • Battery replacement:

        • Remove old batteries

        • Wait 10 minutes

        • Press LED button twice (discharge batteries)

        • Insert new batteries

    • Supervision

      • The Motion Detector sends monitoring signal periodically

      • If signal not received → “Accessory Failure” in app + optional push notification

    • Sleep timer

      • Once motion detection activated, enters ~one-minute sleep mode (no signals).

      • Further motion within this period adds one further minute, up to three min. max.

    • Pet immunity (Jumper JP3)

      • ON = Pet immunity disabled

      • OFF (default) = Pet immunity enabled (ignores pets of up to 25 kg)

    • Sensitivity adjustment (Jumper JP4)

      • ON (default) = increased sensitivity

      • OFF = normal sensitivity

    Installation
    1
    Switch on

    Remove the battery-isolation strip to switch on the detector.

    2
    Registering with the app

    Follow the instructions in the app to add the Motion Detector.


    3
    Alternatively: Add the Motion Detector manually

    1. Put Base Station in pairing mode (press Reset/Learn for six seconds until LED flashes blue).

    2. Press and hold LED indicator on detector for three seconds (LED lights up).

    3. Success = one beep from base station. If the detector has not been added within 25 seconds, please repeat the pairing process. 

    NOT AVAILABLE

    Tip:

    Give each detector a uniquely name for easy identification.

    4
    Placing/mounting the Motion Detector

    • Mount on flat wall or in corner → widest coverage

    • Keep field of view clear (no curtains, furniture, etc.)

    • Recommended mounting height: 2.4 m

    • Higher mounting = larger pet-immune zone, but bigger blind spot below

    • Choose a location to which animals cannot climb.

    • Do not aim the device at staircases.

    • The objective is that intruders should move sideways across the field of view.

    • Mounting:

      • With screws and wall plugs

      • Alternatively, with double-sided adhesive pads (included)

    NOT AVAILABLE

    Limitations

    • Not for outdoor use

    • Avoid having large obstacles in detection area

    • Avoid direct sunlight

    • Avoid damp or condensatiuon-prone areas

    • Avoid moving objects (e.g., curtains)

    • Avoid reflective surfaces (e.g., mirrors, windows)

    • Do not install near AC/heaters

    • Avoid reflected IR signals (may cause false alarms)

    5
    Testing the Motion Detector

    Test the detector by walking past it. Check whether you receive a notification on your mobile phone.

    Congratulations! The installation of your Motion Detector is complete.

    Setting from device

    Sensitivity / Pet immunity (by internal Jumper setting)

    Button functions

    Test button, Learn button

    Pet immunity

    Up to 25 kilograms

    Sleep timer

    1 minute, extendable up to 3 minutes maximum

    PIR motion sensor

    Range 12 metres

    Horizontal angle

    90°

    Vertical angle

    52°

    Installation height

    2.4 metres

    Power source

    1.5 V, 2 AA alkaline batteries

    Battery life

    3 years (actual battery life may vary depending on settings, the environment and usage)

    Low battery threshold

    2.65 V

    RF frequency

    868 MHz

    Wireless range

    300 metres in open space

    Operating temperature

    −10°C to 45°C (14°F to 113°F)

    Operating humidity

    Up to 85% (non-condensing @ 23°C)

    Dimensions

    75 x 75 x 43.5 mm

    Weight

    77 g (battery excluded)