Smoke Detector

The Smoke Detector reliably protects against fire hazards.

With multi-sensor technology, it distinguishes between fast-burning flames and smoldering fires while reducing false alarms caused by cooking smoke.

• Wireless smoke detector with multi-sensor technology

• Differentiates everyday smoke from real emergencies

• Reduces nuisance alarms

• Alerts with buzzer, LED, and Base Station signal

• LED indicator

  • Red LED:

    • Quick flash: Alarm triggered

    • Flashes every second: Smoke detector in alarm silence mode

    • Flashes every 2 seconds: Warm-up phase / calibration

    • Flashes every 4 seconds together with orange: Low battery

    • Brief flash: When the Learn/Test button is pressed to check device function or for system pairing

    • 6 brief flashes: Signal is being transmitted

  • Orange LED:

    • Flashes every second: Calibration failed

    • Flashes every 4 seconds together with red: Battery exhausted

    • Flashes every 5 seconds: Smoke detection failed or device malfunction

    • Flashes every 45 seconds: Low battery

  • Test/Learn button:

    • Short press:

      • Send test signal

      • Check smoke chamber

      • Silence alarm (9 min.)

      • Pair with Base Station

    • Press and hold for 10 seconds:

      • Start calibration
        

• Battery

  • Uses 3 × CR123 3V lithium batteries

  • Automatic battery check every 25 seconds

  • If battery is low: Orange LED + signal to base station + beep every 45 seconds

  • If battery is exhausted: Red + orange LEDs flash every 4 seconds

  • Replacement: Remove old batteries → wait 10 min → press button twice → insert new batteries

  Note:
  In low battery warning mode, the beep will be silenced for 7 days after the first button press. It cannot be muted again after that.

• Dust detection

  • The detector regularly checks the optical chamber for excess dust

  • If dust is detected, it reports to the panel with a cleaning request

  • If the chamber isn’t cleaned and too much dust accumulates, a maintenance warning is issued

• Supervision

  • The Smoke Detector sends periodic supervision signals to the Base Station

  • If no signal is received, the Base Station will indicate a fault

• Alarm activation
  When smoke is detected, the alarm is triggered, a signal is sent to the base station, and the buzzer sounds.

• Smoke detection

  • The smoke detector checks air quality every 8 seconds

  • If the smoke level exceeds the threshold, the alarm sounds and remains active until levels drop

  • The red LED flashes rapidly during alarm

• Alarm silence

  • Pressing the test button during alarm will silence it for 9 minutes

  • The red LED flashes once per second. If smoke falls below threshold during silence, a two-tone beep sounds and normal mode resumes.

  • If smoke rises or exceeds a second threshold, the alarm will sound again and can no longer be silenced by the button.

• Auto-Calibration

  • After first installation, auto-calibration runs after 4 hours, then every 15 days

  • During calibration, the red LED flashes (every 2 seconds, about 50 sec)

  • If calibration fails, the orange LED flashes every second and a fault is reported. Flashing can be stopped by removing/reinserting the batteries or by starting manual calibration

  • If calibration fails again, the orange LED will flash constantly and continuous beeping occurs—remove batteries briefly and reinsert

  Note: If auto-calibration fails, the alarm uses the last successful value. For best results, calibrate the detector at its permanent location.

• Recalibration

  • Hold test button 10 sec., release at 2 beeps

  • After 5 sec. beep, calibration starts (red LED flashes every 2 sec.)

  • Lasts ~1 min; retries up to 9 min if fails

  • Success: Two-tone beep, red LED off, normal mode

  • Fail: Continuous beep + orange LED flashes

  • Remove battery → press test button twice → insert battery → restart

• Test your Smoke Detector weekly using the test button to ensure it works properly.

• Clean the detector at least every 6 months: gently vacuum dust from the detection chamber and vents.

• Wipe the casing with a damp cloth, do not allow water inside. Avoid using cleaning agents.

• Avoid spraying aerosols such as air fresheners or hairspray near the detector.

• Never paint or modify the detector.

• The smoke detector has a maximum lifetime of 10 years. Replace it immediately after this period.

• A replacement date should be marked on the back of the detector.